7800N, IPv6 and the Zen Trial

Post Reply
bsdnazz
Posts: 5
Joined: Tue Sep 29, 2015 8:20 pm

7800N, IPv6 and the Zen Trial

Post by bsdnazz »

Hi,

Has any one had any luck getting a 7800N working on the Zen IPv6 trial?

I've got some trial IP addresses, have enabled IPv6 on my 7800N (currently on firmware V 1.06e) but with no joy.

Any clues or pointers out there?
billion_fan
Posts: 5374
Joined: Tue Jul 19, 2011 4:30 pm

Re: 7800N, IPv6 and the Zen Trial

Post by billion_fan »

bsdnazz wrote:Hi,

Has any one had any luck getting a 7800N working on the Zen IPv6 trial?

I've got some trial IP addresses, have enabled IPv6 on my 7800N (currently on firmware V 1.06e) but with no joy.

Any clues or pointers out there?
Have you enabled 'Ipv6 Autoconfig' as shown on the attached screen shot??
You do not have the required permissions to view the files attached to this post.
bsdnazz
Posts: 5
Joined: Tue Sep 29, 2015 8:20 pm

Re: 7800N, IPv6 and the Zen Trial

Post by bsdnazz »

Yes, IPv6 autoconfig is set.
7800n_status.png
7800_WAN_profile.png
7800n_LAN_IPv6_Autoconfig.png
You do not have the required permissions to view the files attached to this post.
bsdnazz
Posts: 5
Joined: Tue Sep 29, 2015 8:20 pm

Re: 7800N, IPv6 and the Zen Trial

Post by bsdnazz »

and...
7800N_ARP_Table.png
7800N_PC_Interfaces.png
You do not have the required permissions to view the files attached to this post.
bsdnazz
Posts: 5
Joined: Tue Sep 29, 2015 8:20 pm

Re: 7800N, IPv6 and the Zen Trial

Post by bsdnazz »

Nearly there!

Having run a shed load of netsh commands to disable various IPv6 tunnel interfaces I can get IPv6 working if I use stateful configuration. If I try and use stateless autoconfiguration Windows 7 goes not get an IPv6 address. I want to use stateless to I get fixed MAC address based IPv6 addresses.

Might it be worth upgrading my firmware to 1.06h?
billion_fan
Posts: 5374
Joined: Tue Jul 19, 2011 4:30 pm

Re: 7800N, IPv6 and the Zen Trial

Post by billion_fan »

bsdnazz wrote:Nearly there!

Having run a shed load of netsh commands to disable various IPv6 tunnel interfaces I can get IPv6 working if I use stateful configuration. If I try and use stateless autoconfiguration Windows 7 goes not get an IPv6 address. I want to use stateless to I get fixed MAC address based IPv6 addresses.

Might it be worth upgrading my firmware to 1.06h?
Yes you can, I would suggest upgrading to 1.06h.dt2
billion_fan
Posts: 5374
Joined: Tue Jul 19, 2011 4:30 pm

Re: 7800N, IPv6 and the Zen Trial

Post by billion_fan »

billion_fan wrote:
bsdnazz wrote:Nearly there!

Having run a shed load of netsh commands to disable various IPv6 tunnel interfaces I can get IPv6 working if I use stateful configuration. If I try and use stateless autoconfiguration Windows 7 goes not get an IPv6 address. I want to use stateless to I get fixed MAC address based IPv6 addresses.

Might it be worth upgrading my firmware to 1.06h?
Yes you can, I would suggest upgrading to 1.06h.dt2
On our Enta line, I normally setup IPv6 manually

Attached screen shots (other ISP's eg IDnet or Andrew & Arnold use the auto configuration, the later has been using the 7800N for some years now with IPv6)
You do not have the required permissions to view the files attached to this post.
Post Reply